CCNA 4 Chapter 1 2017 Exam Answers 100%

CCNA 4 Chapter 1 Exam Answers Full

  1. You want to verify the K metrics that EIGRPv6 is using. Which command will display the K metrics?
    A. Router#show running-configuration
    B. Router#show ip protocols
    C. Router#show ipv6 eigrp interfaces
    D. Router#show ipv6 protocols
  2. Which command will help you verify that a router has created an adjacency with EIGRPv6?
    A. Router#show ipv6 eigrp
    B. Router#show ipv6 eigrp adjacency
    C. Router#show ipv6 eigrp database
    D. Router#show ipv6 eigrp neighbors
  3. Which command will show only the EIGRPv6 routes?
    A. Router#show ipv6 route
    B. Router#show ipv6 route eigrp
    C. Router#show ipv6 eigrp
    D. Router#show ipv6 eigrp route
  4. You need to verify the interfaces that are participating in EIGRPv6. Which command will show this?
    A. Router#show ipv6 interface
    B. Router#show ipv6 eigrp neighbors
    C. Router#show ipv6 eigrp topology
    D. Router#show ipv6 protocols
  5. Which command will change the hello timer for EIGRPv6 ASN from 10 to 5 seconds?
    A. Router(config)#ip hello-timer eigrp 10 5
    B. Router(config)#ipv6 hello- interval eigrp 10 5
    C. Router(config-rtr)#ipv6 hello-interval eigrp 5
    D. Router(config-if)#ipv6 hello-interval eigrp 10 5
  6. Which statement is true for EIGRP but not for EIGRPv6?
    A. Interfaces must be on the same subnet for an adjacency to form.
    B. K metrics must match for an adjacency to form.
    C. Hello and holddown timers must match for an adjacency to form.
    D. Router IDs must match.
  7. You need to calculate a variance for EIGRPv6. Which table will allow you to calculate the variance for unequal-cost load balancing?
    A. Router#show ipv6 eigrp adjacency
    B. Router#show ipv6 eigrp topology
    C. Router#show ipv6 eigrp interfaces
    D. Router#show ipv6 eigrp neighbors
  8. What is the maximum hop count for RIP?
    A. 15 hops
    B. 100 hops
    C. 255 hops
    D. 16 hops
  9. Which statement is true about RIPv2 advertisements?
    A. RIPv2 allows for neighborship through hello packets.
    B. RIPv2 broadcasts only updates on all active interfaces.
    C. RIPv2 multicasts the full routing table every 30 seconds.
    D. RIPv2 multicasts the full routing table every 60 seconds.
  10. Which metric does RIPv2 use to calculate routes?
    A. Delay
    B. Bandwidth
    C. Hop count
    D. Bandwidth and delay
  11. Which multicast address does RIPv2 use for advertising routes?
    A. 224.0.0.5
    B. 224.0.0.9
    C. 224.0.0.6
    D. 224.0.0.2
  12. When RIP is configured on a router, what must be configured to allow for classless routing?
    A. Router(config)#ip classless
    B. Router(config)#router rip v2
    C. Router(config-router)#ip classless
    D. Router(config-router)#version 2
  13. You need to configure the advertisement of the network 192.168.1.0/24 for RIPv2. Which command will achieve this?
    A. Router(config-router)#network 192.168.1.0
    B. Router(config-router)#network 192.168.1.0 0.0.0.255
    C. Router(config-router)#network 192.168.1.0/24
    D. Router(config-router)#network 192.168.1.0 255.255.255.0
  14. Which command will allow you to see the next advertisement interval for RIPv2?
    A. Router#show ip protocols
    B. Router#show ip rip database
    C. Router#show ip rip
    D. Router#show ip interface
  15. Which command will allow you to inspect RIPv2 calculations for routes discovered?
    A. Router#show ip protocols rip
    B. Router#show ip rip database
    C. Router#show ip interface
    D. Router#show ip rip topology
  16. You have RIPv2 configured on an Internet-facing router. Which command will propagate the default route to all other RIPv2 routers?
    A. Router(config-router)#network 0.0.0.0
    B. Router(config-router)#default-route advertise
    C. Router(config-router)#network 0.0.0.0 default
    D. Router(config-router)#default-information originate
  17. Which command will allow you to inspect RIPv2 advertisements?
    A. Router#show ip protocols
    B. Router#debug rip
    C. Router#show ip rip
    D. Router#debug ip rip
  18. You need to advertise the routes of 192.168.1.0/24, 192.168.2.0/24, and 192.168.3.0/24. Which configuration will achieve this?
    A. Router(config-router)#network 192.168.0.0
    B. Router(config-router)#network 192.168.1.0
    Router(config-router)#network 192.168.2.0
    Router(config-router)#network 192.168.3.0
    C. Router(config-router)#network 192.168.0.0/16
    D. Router(config-router)#network 192.168.0.0 0.0.255.255
  19. You have RIPv2 configured on an Internet-facing router. Which command will suppress RIPv2 advertisements on the interface link?
    A. Router(config-if)#ip rip passive-interface
    B. Router(config-if)#rip passive-interface
    C. Router(config-router)#passive-interface serial 0/0
    D. Router(config-if)#ip rip suppress-advertisement
  20. What is the default invalid timer for RIPv2?
    A. 60 seconds
    B. 90 seconds
    C. 180 seconds
    D. 240 seconds
  21. Which is a problem with using RIPv2 in a network?
    A. Complex configuration
    B. Slow convergence
    C. The use of broadcasts
    D. Routing support for classless networks
  22. Which technique is used to stop routing loops with RIPv2?
    A. Split horizons
    B. Advertisement intervals
    C. Zoning
    D. Invalid timers
  23. Which algorithm does RIPv2 use to calculate routes?
    A. Shortest Path First
    B. Dijkstra
    C. Bellman-Ford
    D. DUAL

Leave a Reply